Free shipping to most Metro areas. Regional areas may incur additional shipping charges; please see shipping policy for more information.

Fuel Manager Pre-Filter + Provent Dual Kit (Single Bracket)

$730.45$849.45 Inc. Gst

Direction Plus™ Fuel Manager Pre-Filter + ProVent Dual Kit protect your engine against costly injector failure.

FUEL MANAGER

Direction Plus™ Pre-Fuel Filter will be installed between the fuel tank and the O.E.M fuel filter which will remove the majority of water and particle contamination, leaving the O.E.M fuel filter to do the final and finer filtration. This ensures you are maximising the protection of your diesel fuel system.

PROVENT OIL SEPARATOR

Direction Plus™ ProVent oil separator protects your diesel engine by reducing the amount of oil entering the engine from blow-by gas in the crankcase ventilation system. By not fitting a Direction Plus™ ProVent system, it is likely that your engine will experience a progressive reduction in performance.

Direction Plus™ ProVent system is specifically designed to separate and redirect oil and air from blow-by gas produced from within the crankcase as it also provides the option of returning the oil back to the sump.

*DUAL KIT INSTALLED IN SUMNER PARK FOR $99

Calulate Shipping Cost

SKU: N/A Category:

Additional information

Weight10 kg
Make

Nissan, Toyota, Mazda, Ford, Isuzu

Model

Navara NP300, LC70 2012-17, LC70 2018-, BT-50 2020 -, Ranger 2011 -, D-Max 2020 -, BT-50 2011 – 20

Reviews

There are no reviews yet.

Be the first to review “Fuel Manager Pre-Filter + Provent Dual Kit (Single Bracket)”

Your email address will not be published. Required fields are marked *

  • Many enthusiasts consider the thicker the plate the better! This is true to a point but what some “experts” don’t consider is when your plates sustain a hit the pressure and shock has to be absorbed somewhere. If the plate has no flex what so ever the shock is then put back into the mounts which are welded to your chassis. It is much easier and cheaper to replace bash plates after a few years rather than repairing your mounts or chassis!

    We offer a range of thicknesses based on your preference, vehicle and type of 4 wheel driving. With plates ranging from 3mm to 4mm for the more common dual cabs through to 4mm standard for heavier vehicles.

  • After countless 4wd trips the one thing I kept replacing the most was my underbody protection. Although they did get a good beating the main problem was the rust factor, especially from my love of beach driving.

    My car would look great all polished and washed except for underneath that was bent out of shape and covered with surface rust. I designed a set out of stainless steel because of the resistance to corrosion and the strength to get a better, more durable life out of my bash plates.

    The stainless steel comes in a 2b matte grey finish which holds up great against scratching and with the extra strength of the stainless I’ve tried my best to knock them out of shape with no success. If you are after a bash plate that you would like to put on and not have to change every 6 months stainless is the way to go.

  • Built using qulaity stainless steel, our Bash Plates provide the perfect weight to strength ratio for your 4×4. As each Make and Model is different so too is the weight of each plate. However, as a general rule, a 3 piece set of 3mm thickness, usually weighs between 24kg & 30kg, while a 3 piece set of 4mm thickness, usually weighs between 35kg & 40kg.

    Please consult the product page of the vehicle you’re interested in for an accurate weight for those Bash Plates.

  • Our aim is to consistently maintain our stock levels so that we can get our plates to you as soon as poosible. However, in the event your plate is unavailable, the turnaround is generally between 1 to 2 weeks. This timeframe is well below the industry average as our plates are made right here in Brisbane, Australia!

  • Our plates are designed to fit with a large range of bull bar setups. If your 4WD currently retains the factory plates, and has a bull bar installed, then our plates will fit. The majority of our bash plates support a diff drop, however, we advise you consult the individual product pages for more information regarding the make and model of the 4WD you wish to fit plates to.

  • In a market saturated with an endless list of must have upgrades for your 4×4 often underbody protection is overlooked. Vehicle manufactures do not consider bash plates essential to the performance of the car even though they are producing cars for offroad use.

    Over the years, the market has seen a shift away from the older live axle cars to the more comfortable riding independent front suspension “IFS”. Whilst making the car more pleasant to drive this means vital components such as the radiator, sump, diff actuator and transfer case become more vulnerable.

    Vehicle owners are often unaware or reluctant to invest in bash plates as they consider their offroading to be tame or “only beach use”. Some of the worst damage we have seen to the underside of cars has been sustained on the beach navigating a cutting or hitting a washout at speed. Often the damage will render the car un-driveable with split radiators or damaged actuators making the car 2wd.

    Bash plates should be one of the first modifications carried out before heading offroad. The damage that can occur, the cost of recovery and repairs vs the purchase price is a simple equation.

[]